Cotton10

Whirl Grip Floss Stabilizer
This patented item really prevents the cotton candy from flying
out of the pan. The plastic screening material is held tightly in 6
places, with space behind it between the clips. The floss readily
adheres to the screening and makes spinning a cotton candy
cone very easy. A “must” for every cotton candy operator. Six
stainless clips included.
#3010NM Whirl Grip Floss Stabilizer for the
#42040NM Non-Metallic Floss Pan

		We have listed some of the common repair parts for your cotton candy machines, but you should refer to your instruction book for complete listings. If you have lost your book, we’ll send another.
When you sell a bag of Cotton Candy for $1.00, $2.00, $3.00 and up, you can not afford to have “down time.” If you operate your Gold Medal Floss machine according to instructions, you should get years and years of dependable service. However, there are a few “repair/replacement” parts that are smart to have on hand. (Items that you can’t buy at the local hardware store, for example.) Note: None of the maintenance kits include a replacement floss band. The Jet Age technology we apply to the insulation on a floss band has created a virtual lifetime expectation. The Econo Floss/Floss Boss Kits include a motor switch and heat switch. #3198 Whirlwind Maintenance Kit #3199 Tornado Maintenance Kit #3197 Econo-Floss Maintenance Kit
#3197 Kit includes: #20010 Eight Leather Floaters #42041 One 10, 24 x 2" Set Screw #42072 One Spin Tite Nut Driver #42073 One Hex Socket Key, 1/8 " Long Arm #42075 One Small Roll 1/2 " wide Abrasive Cloth #42078 One Screw Driver #42131 One Parts Manual #42138 Four Brush Holder Caps	#42139 Four Brush Holder Terminals #42140 Eight Carbon Brushes #42436 Two Dual Brush Holders with Leads #42305 One Copper Terminal Assembly #43018 One Tool Box #20005 One Floss Ribbon #47155 Four Rubber Feet #42798 One Econo Floss/ Floss Boss Rocker Style Heat Switch Additional Misc. Screws	#20006 Suspension Springs, ea. #20050 Head Screws 21/4" (6 cm) for Cast Whirlwind #42041 Head Screws 2" (5 cm) for Lo Profile #20011 Head Gaskets 5" (13 cm) for Whirlwind #43007 Head Gaskets 7" (18 cm) for Tornado #20010 Leather Floaters #42075 10 ft. roll of Abrasive Cloth, For slip rings #42017 3 pos. Heat Switch For X-15, DXWW & Tornado (if purchased prior to early 1995) #42018 Motor Switch for X-15, For DXWW & Tornado (if purchased prior to early 1995)	#42334 Brush Holder Assembly, Red wire #42335 Single Brush Holder, White wire #43141 Motor Switch, 30 Amp #43142 Heat Switch, 3 position #20033 BrushSpring #20034 Carbon Brush #42020 Heat Control For DXWW & Tornado #42140 Econo-Floss Brushes #42380 Econo-Floss Double Floss Brush Holder #42216 Head Gaskets 51/2" (14 cm) #42217 Head Gaskets, 7" (18 cm) #47155 Rubber Feet
#3198 and #3199 Kits contain the appropriate ribbons, brush springs, replacement brushes, etc. that are appropriate for the machine. If you have the H.O. version, this type machine requires two single bands and is priced accordingly on special order.

Floss Machine Overhaul Service
If your machines get heavy use, you may want the head turned down in a precision
lathe – you might want new ribbons – and a general look-see overhaul on whatever is
needed. We always replace the ribbons with new and, if possible, burn the carbon out
of your old ribbons and return them to you. You’ll be financially ahead if you get a
professional winter overhaul once every few years. Call for scheduling – available
time fills up quickly.



Buy a floss pan cover for each machine – Cover up when machines are not in use. Reinforced plastic fabric with elastic edge. #3121 Floss Pan Cover Each Shipping weight 1 lb.	Specially designed stainless steel scoop makes it easy to feed your mixed Flossugar into the spinner-head. Tapered – holds over a pound of sugar. Try one today. #3027 Flosskoop Shipping weight 1 lb.

Page 58